Altronix ACM4CB Installation Instructions Manual de usuario descargar pdf (Pagina 2)

- 2 - ACM4 series

Overview:

These units convert one (1) 12 to 24 volt AC or DC input into four (4) independently controlled fused or PTC protected

outputs. These power outputs can be converted to dry form “C” contacts (ACM4 only). Outputs are activated by an open

collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button,

PIR, etc. The units will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes,

Magnetic Door Holders, etc. All interconnecting devices must be UL Listed. Outputs will operate in both Fail-Safe and/

or Fail-Secure modes. Units are designed to be powered by one common power source which will provide power for both

the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board

operation and the other for lock/accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or

may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of

the four (4) outputs.

Configuration Reference Chart:

Altronix

Model

Number

Outputs

Fuse

Protected

Outputs

PTC

Protected

Outputs

Output

Ratings

Class 2 Rated

Power

Limited

Agency

Listings

UL Listings and

File Numbers

ACM4

x --- 3 amp ---

UL File # BP6714

UL Listed for Access Control

System Units (UL 294).

“Signal Equipment” Evaluated to CSA

Standard C22.2 No.205-M1983

ACM4CB

--- x 2 amp x

Specifications:

• 12to24voltACorDCoperation(settingnotrequired).

• InputRatings(ACM4/ACM4CBonly):

- 12VDC @ 0.4 amp or 24VDC @ 0.2 amp.

• Powersupplyinputoptions:

a) One (1) common power input (board and lock power).

b) Two (2) isolated power inputs (one (1) for board power and one (1) for lock/hardware power).

• Four(4)AccessControlSystemtriggerinputs:

a) Four (4) normally open (NO) inputs.

b) Four (4) open collector sink inputs.

c) Any combination of the above.

• Four(4)independentlycontrolledoutputs:

a) Four (4) Fail-Safe and/or Fail-Secure power outputs.

b) Four (4) dry form “C” 5 amp rated relay outputs (ACM4 only).

c) Any combination of the above (ACM4 only).

• Four(4)auxiliarypoweroutputs(unswitched).

• Outputratings:

- Fuses are rated 3 amp each.

- PTCs are rated 2.5 amp each.

• Mainfuseisratedat10amp.

Note: For Models ACM4/ACM4CB refer to the Total Output Chart on Page 2.

Note: Operating temperature range should be 0 to +49

• RedLEDsindicateoutputsaretriggered(relaysenergized).

• FireAlarmdisconnect(latchingornon-latching)isindividuallyselectableforanyorallofthefour(4)outputs.

 FireAlarmdisconnectinputoptions:

a) Normally open (NO) or normally closed (NC) dry contact input.

b) Polarity reversal input from FACP signaling circuit.

• FACPoutputrelay(form“C”contactrated@1amp28VDCnotevaluatedbyUL).

• GreenLEDindicateswhenFACPdisconnectistriggered.

• Removableterminalblocksfacilitateeaseofinstallation.

BoardDimensions(approximate):5.125”Lx3.625”Wx1.25”H(ACM4andACM4CB).

Sub-Assembly

SECURITY

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Altronix ACM4CB Installation Instructions Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios para eléctrica Altronix ACM4CB Installation Instructions