Altronix ACM8E Installation Instructions Manual de usuario descargar pdf (Pagina 2)

Overview:

hese units convert one (1) 12 to 24 volt AC or DC input into eight (8) independently controlled fused or PTC protected

utputs. These power outputs can be converted to dry form “C” contacts (ACM8 & ACM8E only). Outputs are activated

y an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad,

Push Button, PIR, etc. The units will route power to a variety of access control hardware devices including Mag Locks,

Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. Units are

designed to be powered by one common power source which will provide power for both the board operation and locking

devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock

/ accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other aux-

iliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

ACM8 & ACM8CB Series Configuration Reference Chart:

ACM8 x - 3.5 amp *

ACM8CB - x 2.5 amp x

ACM8E x - 3.5 amp x *

ACM8CBE - x 2.5 amp x x

*When used with Class 2 Rated Power Limited power supply.

Specifications:

• 12 to 24volt AC or DC operation (setting not required).

(.6 amp @ 12volt, .3 amp @ 24volt current consumption with all relays energized).

• Power supply input options:

a) One (1) common power input (board and lock power).

b) Two (2) isolated power inputs (one (1) for board power and one (1) for lock/hardware power).

• Eight (8) Access Control System trigger inputs:

Eight (8) normall

y open (NO) inputs.

b) Eight (8) open collector sink inputs.

c) Any combination of the above.

•

Eight (8) independentl

y controlled outputs:

a) Eight (8) Fail-Safe and/or Fail-Secure power outputs.

Eight (8) dr

y form “C” 5 amp rated relay outputs (ACM8 & ACM8E only).

y combination of the abo

e (ACM8 & ACM8E only).

• Eight (8) auxiliary power outputs (unswitched).

•

Output ratings:

- Fuses are rated 3.5 amp each.

- PTCs are rated 2.5 amp each.

• Main fuse is rated at 10 amp.

Note: T

otal output cur

rent is determined by the power supply, not to exceed a maximum of 10 amp total.

• Red LEDs indicate outputs are triggered (relays energized).

• Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.

Fire Alarm disconnect input options:

a) Normally open (NO) or normally closed (NC) dry contact input.

olarity re

ersal input from F

ACP signaling circuit.

• FACP output relay (form “C” contact rated @ 1 amp 28VDC not evaluated by UL).

• Green LED indicates when FACP disconnect is triggered.

• Removable terminal blocks facilitate ease of installation.

Board Dimensions (appro

ximate): 8”L x 4.5”W x 1.25”H (A

CM8 and

CM8CB)

Enclosure Dimentions: 15.5”H x 12”W x 4.5”D (ACM8E and ACM8CBE)

Altronix

Model Number

Fuse Protected

Outputs

PTC Protected

Outputs

Output Ratings

Agency Listings

UL Listings and

File Numbers

Enclosure

Class 2 Rated

Power Limited

- 2 -

UL File # BP6714

UL Listed for Access Control

System Units (UL 294).

“Signal Equipment” Evaluated to

CSA Standard C22.2

No.205-M1983

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Altronix ACM8E Installation Instructions Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios para eléctrica Altronix ACM8E Installation Instructions