Altronix SMP10 Installation Instructions Manual de usuario descargar pdf

Overview:

SMP10 power supply/charger converts low voltage AC input into 12VDC or 24VDC @ 10 amp of continuous supply

current (refer to specifications). This general purpose power supply has a wide range of applications for access control,

security and CCTV system accessories that require additional power (refer to Voltage Output/Transformer

Selection Table).

Specifications:

Input:

• Input24VACor28VAC,175/300VA(refertotransformerselectiontable).

Output:

• 12VDCor24VDCswitchselectable.

• 10ampcontinuoussupplycurrentat12VDC-24VDC*.

• Filteredandelectronicallyregulatedoutput.

Battery Backup:

• Built-inchargerforsealedleadacidorgeltypebatteries.

• Maximumchargecurrent700mA.

• Batteryisfuseprotected.

• Automaticswitchovertostand-bybattery(zerovoltagedrop).

Additional Features:

• Thermaloverloadandshortcircuitprotection.

• ACinputandDCoutputLEDindicators.

• Includesbatteryleads.

BoardDimensions(approximate):7”Lx4.25”Wx2.3”H

*Specifiedat25˚Cambient.

Voltage Output/Transformer Selection Table:

Voltage Switch Position Transformer

12VDC @ 10 amp continuous supply current Closed 24VACor28VAC/175VA

(AltronixmodelT2428175)

24VDC @ 6 amp continuous supply current Open 24VACor28VAC/175VA

(AltronixmodelT2428175)

24VDC @ 10 amp continuous supply current Open 24VACor28VAC/300VA

(AltronixmodelT2428300)

Installation Instructions:

TheSMP10shouldbeinstalledinaccordancewithTheNationalElectricalCodeandallapplicableLocalRegulations.

1. Mount the SMP10 in desired location/enclosure.

2. Connect proper transformer to terminals marked [AC] (refer to Voltage Output/Transformer Selection Table).

 Use18AWGorlargerforallpowerconnections(Battery,DCoutput).

3. SettheSMP10tothedesiredDCoutputvoltagesettingtheswitchestotheappropriatepositions

(refer to Voltage Output/Transformer Selection Table).

4. Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidpotentialdamage.

5. Connectdevicestobepoweredtoterminalsmarked[+DC-] (Fig. 1).

6. Whentheuseofstand-bybatteriesaredesired,theymustbelead

 acidorgeltype.Connectbatterytoterminalsmarked[+BAT-](batteryleadsincluded).

 Usetwo(2)12VDCbatteriesconnectedinseriesfor24VDCoperation.

7. WhenbatteriesarenotusedalossofACwillresultinthelossofoutputvoltage.

SMP10 - Power Supply/Charger

1 2

Indice de contenidos

Pagina 1 - SMP10 - Power Supply/Charger

Overview:SMP10 power supply/charger converts low voltage AC input into 12VDC or 24VDC @ 10 amp of continuous supply current (refer to specifications).

Pagina 2 - Terminal Identification:

LED Diagnostics:Red (DC) Green (AC) Power Supply StatusON ON Normaloperatingcondition.ON OFF LossofAC,Stand-bybatterysupplyingpower.OFF ON No

Comentarios a estos manuales

Sin comentarios

Altronix SMP10 Installation Instructions Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios para eléctrica Altronix SMP10 Installation Instructions. Altronix SMP10 Installation Instructions User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios para eléctrica Altronix SMP10 Installation Instructions