Altronix Netway4ESK Installation Instructions Manual de usuario descargar pdf

NetWay4ESK - 1 -

Netway4ESK - 4-Port Managed PoE+ Switch w/Midspan Injector

Kit includes: Netway4ES and Netway1E

Installation Guide

Rev. 072313

I.T.E. 43KC

Overview:

Netway4ES is a 4-Port Managed PoE+ switch which is designed for installation at the the IDF (Intermediate Distribution

Frame). NetWay4ES allows for system expansion by accommodating up to four (4) IP cameras/devices over a single

CAT-5e or higher structured cable. Power is provided by the NetWay1E midspan injector typically located at the MDF

(Main Distribution Frame). Built-in IP management facilitates remote device reset/control and status monitoring.

Features:

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and

authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.

NetWay1E/1EV and NetWay4ES is not intended to be connected to outside plant leads and should be installed indoors

within the protected premises. The NetWay1E and NetWay4ES is intended for indoor use only.

1. NetWay1E installation:

a. Attach mounting brackets to NetWay1E for wall mount installation (Fig. 5, pg. 7).

Affix rubber pads to NetWay1E for shelf installation (Fig. 6, pg. 7).

b. Plug the grounded AC line cord (included) into the IEC 320 connector of the NetWay1E unit. Plug unit

into a reliable earth grounded socket. When using multiple units the sum of the individual name plate ratings

should not exceed the supply circuit rating.

Note: Do not connect to a receptacle controlled by a switch.

c. Connect structured cable from UL Listed ethernet switch or video server to RJ45 jack marked [IN] on

NetWay1E (Fig. 1, pg. 2).

d. Connect structured cable from NetWay4ES to RJ45 jack marked [OUT] on NetWay1E (Fig. 1, pg. 2).

e. PoE ON LED will illuminate indicating PoE device is turned on (Fig. 1, pg. 2).

f. Connect a device that will provide a low voltage trigger input to terminals marked [--- PoE Shutdown +]

(12VAC-24VAC or 5VDC-24VDC) (PoE Shutdown Voltage Range in Specifications).

When voltage is applied the PoE output will drop to zero volts. When the voltage is removed from the

PoE shutdown terminals the PoE output will supply power to PoE compliant devices (normal condition).

Note: Return to normal operation from shutdown can take about 4 seconds. When PoE is disabled devices may

still present data signals on line pairs of the structured cable.

Agency Listings:

• UL/CULListedforInformation

Technology Equipment (UL 60950-1).

• CEapproved.

Input:

• 84WfromNetway1E.

Power Output:

• Maximum power per port: PoE+ (30W).

• Totalmaximumpower:84W.

Ethernet:

• Connectivity:RJ45,auto-crossover.

• Wiretype:4-pairCat-5orbetterstructuredcable.

• Distance:upto328ft.(100m).

• Speed:10/100BaseT, half/full duplex, auto negotiation.

LED Indicators:

NetWay1E

- AC Power.

- Yellow - IP Link status, Green - 10/100Base-T/active.

LED Indicators (cont’d):

NetWay4ES

- Yellow - IP Link status, Green - 10/100Base-T/active.

Environmental:

• Operating Temperature: 14ºF to 122ºF (--- 10ºC to +50ºC).

• Storage Temperature:

--22ºto158ºF(--- 30º to +70ºC) Storage.

• Humidity:20to85%,non-condensing

Applications:

• Remoteinstallationandpoweringofamanaged

4 port PoE+ switch. Star expansion of remote node to

4 PoE+ cameras/devices.

Mechanical:

•Dimensions(HxWxDapprox.):

1.7” x 5.23” x 8.42” (43.18mmx132.84mmx213.87mm)

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Installation Guide

NetWay4ESK - 1 -Netway4ESK - 4-Port Managed PoE+ Switch w/Midspan InjectorKit includes: Netway4ES and Netway1EInstallation GuideRev. 072313I.T.E.

Pagina 2 - Typical Application:

- 2 - NetWay4ESK2. NetWay4ES installation: a. Mounting: - Attach mounting brackets to NetWay4ES for wall mount installation (Fig. 3, pg. 7).

Pagina 3 - NetWay4ESK - 3

NetWay4ESK - 3 -NetWay4ESK User Interface and Programming:Note: A constant PC connection is not required for proper operations and is used as a loc

Pagina 4 - Network Type:

- 4 - NetWay4ESKFig. 2 - NETWORK SETTING MENU. This menu is for configuring the NetWay4ES units for a network connection.Fig. 3 - SetupNetwork Type

Pagina 5 - Additional Information:

NetWay4ESK - 5 -Additional Information:1. If using DHCP, all settings will be detected automatically. While DHCP is a useful tool for determining

Pagina 6 - (H x W x D approx.):

- 6 - NetWay4ESKNetWay4ES Chassis Mechanical Drawing & Dimensions (H x W x D approx.): 1.7” x 5.23” x 8.42” (43.18mmx132.84mmx213.87mm)F

Pagina 7 - Wall Mount Installation

NetWay4ESK - 7 -Mounting Options:Wall Mount Installation1- Install mounting brackets (A) on the left and right side of rack chassis using four (4)

Pagina 8 - IINetWay4ESK J03M

- 8 - NetWay4ESKAltronix is not responsible for any typographical errors.14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-

Comentarios a estos manuales

Sin comentarios

Altronix Netway4ESK Installation Instructions Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios para eléctrica Altronix Netway4ESK Installation Instructions. Altronix Netway4ESK Installation Instructions User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios para eléctrica Altronix Netway4ESK Installation Instructions