Altronix HubWay LDH8 Installation Instructions Manual de usuario descargar pdf (Pagina 3)

HubWayLDH Active Hub Unit - 3 -

Installation Instructions:

1. SettheinputvoltageselectorswitchlocatedontheleftsideoftheHubWayLDH8/LDH16unit(facingfrontpanel)

for 115VAC or 230VAC operation (Fig.1i,pg.4).

2. Attach mounting brackets to HubWayLDH unit for rack or wall mount installation (Figs.5-6,pg.8). Affix rubber

pads to HubWayLDH for shelf installation (Fig.7,pg.8).

3. Securetheunitinarack,mountunittoawallorplaceunitonashelfasdesired(unitshouldbespacedatleast

 3”fromanyvideomonitors).

4. Setilluminatedmasterpowerdisconnectcircuitbreakertothe(OFF)position(Fig.4,pg.7).

5. PlugthegroundedAClinecord(included)intotheIEC320connectoroftheHubWayLDH8/HubWayLDH16

unit (Fig.1h,pg.4). Insert the plug end of the line cord into a grounded AC receptacle.

6. ConnecttheBNCvideooutputsforHubWayLDH8/LDH16Channels1-8(Channels1-16)tothe

 correspondingvideoinputsontheheadendequipment(DVR)(Fig.1d,pg.4).

7. ConnecttheRS422/RS485outputoftheheadendequipment(DVR)totheone(1)orbothdatainputterminal

 blocksoftheHubWayLDH8orHubWayLDH16unit(polaritymustbeobserved)(Fig.1c,pg.4).

Note: The Data input terminals of the HubWayLDH8 or HubWayLDH16 must be wired in parallel for proper

operation. When using fixed cameras disregard this step.

8. ConnectVideoBalun/Combineratcamera1totheHubWayLDH8orHubWayLDH16unitutilizingCAT-5

or higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked

[Channel 1] of the HubWayLDH8/LDH16 (Fig.1a,pg.4). Plug the RJ45 connector at the opposite end of the

structured cable into the RJ45 jack of the Video Balun/Combiner located at camera 1.

 Repeatsteps6-9foreachadditionalcamera(Channels2-8orChannels2-16).

Note:Anexternalpowersourceisrequiredtopowerthecameras(Figs.2-3,pgs.5-6).Optionally,anAltronix

 HubSat4DPassiveUTPTransceiverHubwithIntegralCameraPowermaybeutilized(Fig.2a,pg.5).

The combined total cable distance must not exceed 3000 ft. for video transmission between the

HubWayLDH8/LDH16 and each camera routed through the HubSat4D.

9. UponcompletionofthewiringsetilluminatedmasterpowerdisconnectcircuitbreakertotheRESET(ON)position

(Fig.4,pg.7).

10. ThevideosignalindicatorLEDs(Red)locatedontherearoftheHubWayLDH8/LDH16willilluminatewhen

video signal is present (Fig.1g,pg.4). If any of these LEDs are not illuminated, there is no video signal for

that corresponding channel.

11. Optimizethepicturequalityforallcamerachannelsbyadjustingthecorrespondingpotentiometers

marked [Picture] (Fig.1e,pg.4).

12. Setgainforallcamerachannelsbyadjustingthecorrespondingpotentiometersmarked[Gain](Fig.1f,pg.4).

1 2 3 4 5 6 7 8

Sin comentarios

Altronix HubWay LDH8 Installation Instructions Manual de usuario Pagina 3